Can I Install A Bathtub Myself?
Can I Install A Bathtub Myself?
Blog Article
Each person has their personal piece of advice on the subject of How to Install a Bathtub.
Mounting a tub isn't exactly rocket science, yet it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard project. If the old bathtub is readily easily accessible, the task can move easily; if you have to open up a wall to eliminate the old tub as well as place the new tub, the job is much harder. In either instance, the project is within a home handyman's abilities, although you will need an assistant to move out the old tub and also set in the new one. See to it you have certified on your own for the job as well as fit attempting it. Instead of employing a professional to take control of a halfway-completed project, it is much better to take into consideration employing one before you start. Chances are you may need a specialist plumber to make tube links.
This write-up will assist you set up a brand-new bathtub in your restroom if you have currently bought a new tub as well as do not require to transform the setup of your previous supply of water pipes.
Your tools as well as product list should comprise the following:
Planning for the Installment
Firstly, the supporting framework supplied with the bathroom must be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make sure that if the tap comes with a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final position.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain any kind of water staying in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the limited access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Bath tub
Utilizing both wooden boards under its feet, position the bathtub in the called for position. The wood boards are helpful in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by examining the spirit level as well as readjusting the feet on the bathtub till the spirit level checks out degree.
To install faucets, fit all-time low of the furthest versatile faucet connector to the proper supply pipeline by making a compression join; after that do the very same for the other faucet.
Activate the supply of water as well as examine all joints and new pipework for leakages and also tighten them if required. Fill up the bath tub and likewise examine the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the producer's user's manual. Tiling and also securing around the bathtub ought to wait up until the bath tub has been used a minimum of when as this will certainly settle it into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly need a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will require decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washing machines are in place between the tap and the sink. Secure the tap in place with the producer offered backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal faucet adapters. The previous kind needs to be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to break a stiff seal, causing the water to penetrate the wall surface in between the bath and the tiling, leading to difficulties with wetness as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components and also fittings. They are sold in tubes and cartridges, and also can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched paper or soft rope. Remember to constantly load the tub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealer can split fairly early if you do not take into account this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or waterproof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been shown that editorial on Tools You Need to Install a New Bathtub through a good friend on another web page. Sharing is good. Helping others is fun. I value reading our article about How to Install a Bathtub.
Click On This Link
Report this page